External h (never over nominal) with IT6. Precision ground pins and bearing journals. At Ø20 mm the h6 limits are 19.987–20.000 mm (0 / -13 µm).

What are the 20 mm h6 limits?

19.987–20.000 mm, deviations 0 / -13 µm, IT6 = 13 µm in the over 18 to 24 mm band.

Engineering

Check ISO fit

h6 Shaft Tolerance

h6 is tighter than h7. It is the usual shaft for an H7/h6 locational sliding fit and for many bearing inner seats that are not an interference class.

h6 · Ø20 mm example · over 18 to 24 mm

Feature

Used when a class could be a hole or a pocket. Shafts are lowercase.

Nominal size (mm)over 18 to 24 mm · IT 18–30 mmFind any class

Type H7, h6, F8, k6, B10, or “20 H7”. Every ISO letter × grade we can compute is listed.

As on a drawing

Shaft (external) · IT6 · precision

Ø20h6

0−0.013

2019.987limits mm

Maximum shaft size

20 mm

Minimum shaft size

19.987 mm

Tolerance

13 µm

es (upper)

0 µm

ei (lower)

−13 µm

IT band

18–30 mm

Shaft catalog row

over 18 to 24 mm · Units: µm

b9	c9	d8	d9	e7	e8	e9	f6	f7	f8	g5	g6	h4*	h5	h6	h7	h8	h9	js5	js6	js7	k5	k6	m5	m6	n5*	n6	p6	r6	s6	t6	u6	x6

Catalog row is the regularly used set. The finder above also lists every other computable class (H11, h4*, n5*, T7, x6, …). * = old JIS extra.

What the code means

External h (never over nominal) with IT6. Precision ground pins and bearing journals.

Formula

h6 at Ø20 mm

es / ei 0 / -13 µm

IT6 = 13 µm

Limits 19.987 / 20.000 mm

Ø20 h6

Size band over 18 to 24 mm. The feature measures 19.987–20.000 mm.

How we use this in the toolroom

We grind pins h6 when they must slide into an H7 hole with almost no shake. Leave it h7 if the fit can be a little easier to assemble by hand.

The numbers come from ISO 286 tables, the same charts Accurate Industries uses in Pune for dies, moulds and precision tooling. AlwaysReach is the browser version of that lookup — see our story.

Other shaft classes

Common hole/shaft pairings

Full type-ahead for every ISO class is on the ISO tolerance calculator. Convert the millimetre result with the unit converter.

Frequently asked questions

What does an H7 hole mean?+

The capital letter is the fundamental deviation for an internal feature; H means the lower deviation is zero (the hole never goes below nominal). The number is the IT grade — IT7 is a precision finishing grade used for bearings, bushings and locational fits. A 20 mm H7 hole is 20.000–20.021 mm.

What is the tolerance of H7? What is an H7 bore?+

H7 is a hole class, not a single micrometre number: the tolerance of H7 is IT7 with a lower limit at nominal. An H7 bore is a reamed location hole — dowel, bush or bearing. This page is an H7 tolerance chart: enter a diameter (20 mm, 30 mm, 65H7, 100H7, 120H7) to read max and min.

Where is the k6 tolerance chart or H8 tolerance chart?+

k6 is a shaft class (transition with H7). Open the k6 tolerance chart for deviations and a 20 mm example. H8 is a hole/pocket class; the H8 tolerance chart also covers an H8 fit such as H8/f7. Neither is the same as H7.

Is h7 the same as H7?+

No. H7 is a hole (internal). h7 is a shaft (external). For 20 mm, H7 is 20.000–20.021 mm and h7 is 19.979–20.000 mm. They sit on opposite sides of nominal and must not be mixed up.

Is a pocket H8 the same as a hole H8?+

The ISO 286 numbers are the same: an internal H8 class is +IT8 / 0 whether it is a cylindrical hole or a pocket width. The calculator lists holes and pockets separately because the usual grades differ — reamed holes are typically H7; milled pockets are typically H8, H9 or H11 — and so the result is labelled as a hole or a pocket, not as a shaft.

How do I read a fit like H7/g6?+

H7 is the hole, g6 is the shaft. Because g is a small negative shaft deviation, H7/g6 is a close running (clearance) fit: the shaft is slightly under nominal and the hole is slightly over, so parts assemble by hand with little play.

Are the values from ISO 286?+

Standard tolerances (IT grades) and fundamental deviations follow ISO 286-1/2 tables for the usual nominal ranges up to 500 mm, including the Δ correction for internal K, M, N and P–S classes. Always confirm critical fits against the current standard and your drawing notes.

Can I enter custom deviations?+

Yes. Switch to custom mode and type upper and lower deviations (in mm or µm). The calculator returns maximum size, minimum size, tolerance width and a diagram of the zone relative to nominal.